WIFI THERMOMETER is a device that, in addition to being used to measure temperatures, reports and alarms if actual temperatures are higher or lower than alarm values. A number of temperature probes can be connected to the device when ordering (display of room temp, fermenter, aquarium, terrarium, boiler, outdoor temperature, etc.) and set the required alarm parameters. Recently, more failures of the STC-1000 temperature controller have been occurring, and this can serve as a cheap addition to overheating and cooling, and with the addition of a gas sensor, as a possible prevention against major problems. A lot of people use the same for alarming at too high a temperature in wood stoves, some use it as an alarm – a reminder of burning …
The PCB board (Motherboard) is of its own design and allows for a more durable and high-quality operation of the device. The application in use allows you to upgrade multiple WIFI devices so you can have complete control of your home systems in one place. It also has the option of LIVE display of certain values on the mobile screen. The same application can be used on a number of mobile devices, tablets,… that you use in your household, or with anyone you share your user data with. For others, the same content is automatically displayed upon login.
On the TFT display of the thermometer, if it is installed, on the bottom line, there are notifications about the strength of WiFi signal if the device is connected to WiFi, Blynk status (B-D mark indicates that Blynk application is not connected, B-C mark indicates that Blynk application is connected to thermometer), mark Ok indicates if the temperature sensor is connected correctly, or mark D if the temperature sensor is not connected or there is a malfunction).
The WiFi thermometer has a KEEZER option. When it is on, you can change the setpoints of the lower and upper temperature of the beer on the tap on the local thermometer page in the management menu. If the temperature is lower, a message about too low temperature appears on the display. Also if it is too high. When the temperature is within the value then a notification is displayed that the beer is at the ideal temperature for consumption. If required, the thermometer housing can be adapted for installation on the door or side of the keezer. The content of the messages on the display can be made to your wish.
Basic device parts:
– 1 temperature sensor on a 1 m long probe that can be extended as needed without affecting the measurement result.
– an error message is also displayed on the cell phone, ie the non-functionality of the home WIFI network.
– Possibility of calibration of individual sensor.
Custom device parts:
– a small 1″ oled screen,
– a big 2″ TFT colour screen,
– an audible alarm that occurs if an individual value exceeds the set value, while at the same time an ALARM mail is sent and an alarm notification is sent on the mobile phone.
– smoke sensor for 8 types of gases,
– graphical representation of temperature and other measured data on Blynk app.
The device connects to a 5V micro USB mobile phone charger and requires WIFI networking to send data. Micro USB does not come with the thermometer.
Nautilis thermometer management system
View and edit thermometer settings (no internet required)
To view and change the device settings, first connect to the WiFi network that the device transmits, which is usually: nautilis_thermometer_one. The network password comes on the paper with the device. After connecting to the network, some devices automatically open the Internet browser, and some require you to open the Internet browser and go to the address: 192.168.4.1
After that, the Nautilis thermometer managment home page opens where you can view and edit the following settings:
Here you must enter the name of your WiFi network – BEWARE OF CAPITAL AND SMALL LETTERS !!!
Your WiFi network password – BEWARE OF CAPITAL AND SMALL LETTERS !!!
In the Blynk server field, enter blynk-cloud.com – if you use the Cloud Blynk server, if you use your local Blynk server then enter its IP address. The Blynk PORT (8080) is already set and it is not entered manually.
Paste or enter the Blynk token in the last field.
Click the SUBMIT button and reboot the device.
Here you change the alarm and sensor settings.
Here you can turn the thermometer audible alarm on or off.
Opening this link will reboot the device
And curent temperature & Firmware version.
How to install BLYNK aplication?
The device is designed to run on the Blynk application, which must be installed on your mobile / tablet.
QR code for Blynk: